Building a Halbach array
Step-by-step instructions for those keen on experimenting
Online since: 07/04/2010,
Number of visits: 586331
2
I'd like to present to you step-by-step instructions on how to build a Halbach array.
The Halbach array is a special arrangement of magnets, which "bend" the magnetic flux: On the one side the magnetic field becomes up to twice as strong, on the other one it decreases.
The longer the arrangement the stronger the effect.
Note from the supermagnete team:
The following video is from our customer Mirko Pafundi and shows a slightly different approach than Mr.
Bos' detailed instructions - you choose your favorite.
Material needed:
- 1 medium-size piece of iron or steel (approx. 20 x 15 cm)
- 1 small piece of iron or steel (approx. 10 x 3 cm)
- Straight piece of non-magnetic material, e.g. copper or wood
- Strong adhesive, e.g. UHU MAX REPAIR
- Small spatula or something similar to apply adhesive
- Transparent adhesive tape
- Waterproof felt-tip pen
- Sand paper
- Neodymium magnets (at least 6), e.g. W-07-N or Q-15-04-04-MN
Assembly:
1. Take the ordered magnets from supermagnete out of the plastic bag.2.
Cut the plastic bag open with scissors or a cutter knife, fold it apart.
3.
Wrap the two iron or steel pieces tightly with the plastic foil.
4.
Fasten the plastic foil with an adhesive tape.
5.
Arrange the selected magnets in a row.
Meaning: a north and south pole is always connected to each other.
6.
Put a small piece of adhesive tape over every magnet.
7.
Mark every north and south pole with a waterproof felt pen (see picture).
8.
Put the magnets with the marked surface facing forward on a medium-size piece of iron.
9.
Pull the magnets apart and arrange them as follows:
- Front row: south poles left and right alternately
- Back row: south poles up and down alternately
Front view
10.
Remove magnets one by one, roughen up the area to the left and right of the marked surface with sandpaper.
Remove sanding residue with a piece of paper.
Put the magnets back on the iron.
11.
Place a small piece of iron on top of the back row of magnets (see picture).
12.
Put glue on the roughened surfaces.
13.
Push the back row between the front row: use a piece of wood or any other non-magnetic material to slowly push the back row in front until all magnets are on one line.
14.
Push the magnets together sideways until the adherends touch each other.
15.
Let the magnet arrangement dry for at least 24 hours.
16.
Remove the iron pieces after drying.
The top piece can be removed easily.
Thanks to the Halbach arrangement, the magnets strongly adhere to the bottom piece though.
How to remove the bottom piece: Place the magnets on the edge of a table (see picture below), hold on to the magnets and slowly push the iron piece downwards.
Now, the Halbach array is complete!
Caution: This magnet arrangement is very strong and breaks easily at heavy collisions!
Articles used
Load...
Block magnet 15 x 4 x 4 mm, heat-resistant, holds approx. 1,7 kg, neodymium, 45M, nickel-plated
| 5 pcs. | 0,80 EUR ea.* | |
| from | 15 pcs. | 0,70 EUR ea.* |
| from | 40 pcs. | 0,61 EUR ea.* |
| from | 80 pcs. | 0,56 EUR ea.* |
| Ask for a rebate from 700 pcs. | ||
Available: 675 pcs.
Cube magnet 7 mm, holds approx. 1,6 kg, neodymium, N42, nickel-plated
| 5 pcs. | 1,02 EUR ea.* | |
| from | 15 pcs. | 0,90 EUR ea.* |
| from | 40 pcs. | 0,80 EUR ea.* |
| from | 80 pcs. | 0,74 EUR ea.* |
| Ask for a rebate from 650 pcs. | ||
Available: 46 060 pcs.
magnet glue, waterproof, without solvents, shelf life of 24 months, 20 g tube
To glue on super magnets
To glue on super magnets
| 1 pc. | 8,38 EUR ea.* (419,00EUR/kg) |
Available: 1 829 pcs.
2 people like this customer project
-Projects are bookmarked in your customer account
keywords
The entire content of this site is protected by copyright.
Copying the content or using it elsewhere is not permitted without explicit approval.
Copying the content or using it elsewhere is not permitted without explicit approval.